Devrim Coskun
BH Lover
I am using Linksys AE1000 Wi-fi Adapter on Vu+Solo2. The adapter is recognized by the STB and I choose DHCP enabled. But STB cannot take IP address. (My image on Vu+Solo2 is BH 2.0.0)
Linksys AE1000 Wi-fi Adapter Problem
- Thread starter Devrim Coskun
- Start date
angelofsky1980
BlackHole Driver Specialist
Devrim Coskun
BH Lover
Could you please confirm the following?
--I will connect the box with RJ45 and configure the network accordingly,
--I will then connect the USB wi-fi adapter,
--I will reboot the box,
--I will connect to the box by PC using putty,
--I will send the commands in your post.
--I will connect the box with RJ45 and configure the network accordingly,
--I will then connect the USB wi-fi adapter,
--I will reboot the box,
--I will connect to the box by PC using putty,
--I will send the commands in your post.
Devrim Coskun
BH Lover
I have uploaded the file wifi.txt as you requested. Thank you in advance.
angelofsky1980
BlackHole Driver Specialist
I suppose your wifi network is a G (54Mbit/s) network called "coskun"...
I suggest to change your Wifi channel because it's the same of one other wireless network and can cause problems.
Devrim Coskun
BH Lover
OK. My wi-fi channel is 1-2412 MHz. I will change it and try again.
So you don't see a driver problem, do you?
So you don't see a driver problem, do you?
angelofsky1980
BlackHole Driver Specialist
It's my opinion that your device is correctly detected and running.
Configure also your box with specific settings (use the option WPA instead WPA/WPA2 or WPA2 instead WPA/WPA2 for example).
Devrim Coskun
BH Lover
I changed the channel, but no change.
angelofsky1980
BlackHole Driver Specialist
Can you try with a static IP address on your box?
Devrim Coskun
BH Lover
I have already tried with static IP address (DHCP disabled). Nothing changed.
I have applied WPA/WPA2 and WPA2. Nothing changes. It detects the wireless connection, but cannot take IP from the access point.
I have applied WPA/WPA2 and WPA2. Nothing changes. It detects the wireless connection, but cannot take IP from the access point.
angelofsky1980
BlackHole Driver Specialist
Your wireless (reading your wifi.txt output) doesen't support WPA2 but only WPA....
Devrim Coskun
BH Lover
Previously I tried with WPA. Then as per your advice, I tried different settings, WPA/WPA2, WPA2.
Nothing changed at all. Do you think I should install the new image 2.0.1?
Nothing changed at all. Do you think I should install the new image 2.0.1?
angelofsky1980
BlackHole Driver Specialist
You should upgrade to 2.0.1 and, next, upgrade online with newest wifi drivers avaiable on the online.
Devrim Coskun
BH Lover
how can i upgrade online? Thank you.
angelofsky1980
BlackHole Driver Specialist
Green button -> Yellow Button -> Black Hole Online Updates (or a similar one)
Devrim Coskun
BH Lover
I upgraded and it said 36 packages have been updated.
But nothing changed.
But nothing changed.
Devrim Coskun
BH Lover
Although I am not very comfortable about my solution, I finally found one.
I changed the encryption method of my wi-fi access point to Non-802.1x WEP. That was the only one that worked with Linksys AE1000.
I think that issue is obviously something to be solved by BH team. Linksys AE1000 couldn't send the correct passphrase to the wi-fi access point, via the encryption methods other than Non-802.1x WEP.
Anyway, thank you for all your support and help.
I changed the encryption method of my wi-fi access point to Non-802.1x WEP. That was the only one that worked with Linksys AE1000.
I think that issue is obviously something to be solved by BH team. Linksys AE1000 couldn't send the correct passphrase to the wi-fi access point, via the encryption methods other than Non-802.1x WEP.
Anyway, thank you for all your support and help.