modena6116
Vu+ Newbie
hello bh club and matrix10.i have a problem plz help me my setopbox is solo2 i installed obh 4.2 then searched satellites i succseed just yah1A(52.5E) searching but not otherwise plz tell my solution before i thank you
One Satellite only found ... why?
- Thread starter modena6116
- Start date
modena6116
Vu+ Newbie
hi bh lovers and matrix10.i have a problem plz help me.my setopbox is solo2 today i installed obh4.2 image but insearching time i sucsseed just one satellite find ( yah1a52.5E)plz tell me my solution ?thanks
nunigaia
Moderator
Why duplicating posts?
Next time, wait for that someone could give, has the answer and time for it!
And, by the way, you are here "OFF TOPIC"
I will move your issue to -> Open BlackHole 4.2 - Solo2 section.
Thread moved to the correct section ( STB * IMAGE )
best regards
nunigaia
modena6116
Vu+ Newbie
excuse me for duplicating posts my dish motorised one lnb and in tuner configuration is advanced and dis 1.2
and found satellite is yah1a (52.5E)
i had bh 3.0.2f but missed the satellites then upgrade image to 3.0.5 but anything not found then i install obh4.2 that found 2 satellites 52.5E and 53E
and found satellite is yah1a (52.5E)
i had bh 3.0.2f but missed the satellites then upgrade image to 3.0.5 but anything not found then i install obh4.2 that found 2 satellites 52.5E and 53E
Matrix10
Administrator
I do not know why you do not use it
usuals configuration if you have DiSeQC motor.
Which is much easier to use and configure if you have a motor.
Those who use advanced are mostly doing it because they do not mechanically set up the antenna as prescribed in the rotor and antenna instructions.
I still advise you to pay attention to the above
to have many years of pleasure to use the installation without any problems.
I must emphasize that this is a precision work
Every millimeter is important for signal strength.
Most importantly is mount the antenna mount/metal tube in the absolute vertical position.
This is essential for easy antenna and motor adjustment.
When the antenna and motor are correctly and precisely positioned
it remains only to write the coordinates of your city into the ususals configuration.
and Scan satellites or use ready made SAT list settings.
The problem you describe to me most looks bad
set elevation and antenna position.
Provided you have used the correct configuration in the box.
About Advanced
In Advanced Configuration
All different positions must be memorized/Save under different numbers
for each satellite separately.
usuals configuration if you have DiSeQC motor.
Which is much easier to use and configure if you have a motor.
Those who use advanced are mostly doing it because they do not mechanically set up the antenna as prescribed in the rotor and antenna instructions.
I still advise you to pay attention to the above
to have many years of pleasure to use the installation without any problems.
I must emphasize that this is a precision work
Every millimeter is important for signal strength.
Most importantly is mount the antenna mount/metal tube in the absolute vertical position.
This is essential for easy antenna and motor adjustment.
When the antenna and motor are correctly and precisely positioned
it remains only to write the coordinates of your city into the ususals configuration.
and Scan satellites or use ready made SAT list settings.
The problem you describe to me most looks bad
set elevation and antenna position.
Provided you have used the correct configuration in the box.
About Advanced
In Advanced Configuration
All different positions must be memorized/Save under different numbers
for each satellite separately.
Do not forget that after each configuration change you need to reboot the box.
Last edited:
I have to use the advanced option, due to having a Channel Master 1.2M dish, and a Jaeger 1224 motor, which is a 36v motor, with 4 wires going from the motor to a V-Box II.
Do you have a similar set up, or as Matrix10 states do you have a simpler Diseqc motor?
It is always easier if you list your satellite set up, in full, so we know best how to advise you.
I have my satellite positions, in the V-Box II, written down, so now I only have to set the satellites, in the tuner menu, to correspond with the V-Box II settings.
This makes it a lot easier, as you can just enter the tuner menu, select Tuner A, which I have going through the V-Box II, select a satellite, configure the settings, including the correct stored position, save it, then go back in to select the next satellite, and keep doing so until all the satellites have been stored.
You don't need to re-boot the receiver, at any point.
Make sure you choose the correct satellite, in Europe some satellites are listed as KU band, KA band, and C band.
Do you have a similar set up, or as Matrix10 states do you have a simpler Diseqc motor?
It is always easier if you list your satellite set up, in full, so we know best how to advise you.
I have my satellite positions, in the V-Box II, written down, so now I only have to set the satellites, in the tuner menu, to correspond with the V-Box II settings.
This makes it a lot easier, as you can just enter the tuner menu, select Tuner A, which I have going through the V-Box II, select a satellite, configure the settings, including the correct stored position, save it, then go back in to select the next satellite, and keep doing so until all the satellites have been stored.
You don't need to re-boot the receiver, at any point.
Make sure you choose the correct satellite, in Europe some satellites are listed as KU band, KA band, and C band.
modena6116
Vu+ Newbie
i thank you so much my masters when i search with sat finder crashing to system with green error in bh image 3.0.5 what is problem my hardware or software?
Last edited:
Your first post stated that you were using Open Black Hole 4.2, now you're using the older Black Hole 3.0.5, and you still haven't provided the relevant information, regarding your system, apart from Solo 2.
Can you please confirm that yo have the VU+ Solo 2, or do you have a different receiver?
The latest Black Hole is 3.0.6.
Can you please confirm that yo have the VU+ Solo 2, or do you have a different receiver?
The latest Black Hole is 3.0.6.
modena6116
Vu+ Newbie
l have vu+ solo2 its original image was bh3.0.2f in early this image being to crashing not shoting down and not recording and 1 week ago not recognizing any satellites only 52.5e because my fixed in its position sat and not connecting my reciver then i change image to bh 3.0.5i but this image crashing again with green error and not found any sat then i install obh4.2 that found one sat(52.5e) in fact my reciver not related to motor i dont know that i do.probably i call to my sat installer agent if l couldnt stablish this problem alone
The last version of Black Hole, for the VU+ Solo 2, is 3.0.6:
http://www.vuplus-community.net/board/threads/black-hole-3-0-6-vu-solo2.37448/
I'm using Open Black Hole 4.2, in which there is a positioner setup option, in the tuner menu, allowing you to select a satellite, go to option, only if they are already stored in the tuner configuration, then move the dish, including fine movements, to maximize the signal quality, and store it.
http://www.vuplus-community.net/board/threads/black-hole-3-0-6-vu-solo2.37448/
I'm using Open Black Hole 4.2, in which there is a positioner setup option, in the tuner menu, allowing you to select a satellite, go to option, only if they are already stored in the tuner configuration, then move the dish, including fine movements, to maximize the signal quality, and store it.
modena6116
Vu+ Newbie
thanks to your attentions. your comments and orders were useful