Ciao a tutti, questo è il mio primo post, complimenti per la community.
Ho appena acquistato da una vendita flash su amazon la chiavetta dvb in oggetto (August DVB-T202), per sostituire la digital key che comunque faceva il suo lavoro.
Su windows ho installato i driver dal sito del produttore per provarla, in gestione periferiche compare col nome "it9135".
Sul vuplus solo se v2 non compare tra i tuner, ho provato prima sulla open blackhole, poi ho flashato l'ultima blackhole ma stessa situazione, da telnet con il comando "opkg list" ho visto che sono già presenti due package per it9135:
media-tree-firmware-dvb-usb-it9135-01 - 0.0+git20140924-r0.11 - Firmware for dvb-usb-it9135-01 Firmware for dvb-usb-it9135-01
media-tree-firmware-dvb-usb-it9135-02 - 0.0+git20140924-r0.11 - Firmware for dvb-usb-it9135-02 Firmware for dvb-usb-it9135-02
grazie in anticipo per l'eventuale supporto
output dsmesg e dvb_debug.txt in allegato
Ho appena acquistato da una vendita flash su amazon la chiavetta dvb in oggetto (August DVB-T202), per sostituire la digital key che comunque faceva il suo lavoro.
Su windows ho installato i driver dal sito del produttore per provarla, in gestione periferiche compare col nome "it9135".
Sul vuplus solo se v2 non compare tra i tuner, ho provato prima sulla open blackhole, poi ho flashato l'ultima blackhole ma stessa situazione, da telnet con il comando "opkg list" ho visto che sono già presenti due package per it9135:
media-tree-firmware-dvb-usb-it9135-01 - 0.0+git20140924-r0.11 - Firmware for dvb-usb-it9135-01 Firmware for dvb-usb-it9135-01
media-tree-firmware-dvb-usb-it9135-02 - 0.0+git20140924-r0.11 - Firmware for dvb-usb-it9135-02 Firmware for dvb-usb-it9135-02
grazie in anticipo per l'eventuale supporto
output dsmesg e dvb_debug.txt in allegato
Code:
root@vusolose:~# dmesg
ahci strict-ahci.0: AHCI 0001.0300 32 slots 3 ports 6 Gbps 0x3 impl platform mode
ahci strict-ahci.0: flags: ncq sntf stag clo pmp slum part
scsi0 : ahci_platform
scsi1 : ahci_platform
scsi2 : ahci_platform
ata1: FORCE: PHY spd limit set to 1.5Gbps
ata1: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x100 irq 33
ata2: SATA max UDMA/133 mmio [mem 0x10181000-0x10190fff] port 0x180 irq 33
ata3: DUMMY
brcmstb_nand: NAND controller driver is loaded
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet: configuring instance #0 for internal PHY
bcmgenet bcmgenet.0 eth0: link down
__clk_disable: enet [0]
bcm40nm_pm_genet_disable 00
__clk_disable: network [0]
bcm7429_pm_network_disable 00
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: moca_genet [1]
bcm40nm_pm_genet1_enable 00
__clk_enable: moca [1]
bcm40nm_pm_moca_enable 00
ata1: SATA link down (SStatus 0 SControl 310)
No PHY detected, not registering interface:1
__clk_disable: moca [0]
bcm40nm_pm_moca_disable 00
__clk_disable: moca_genet [0]
bcm40nm_pm_genet1_disable 00
__clk_disable: network [0]
bcm7429_pm_network_disable 00
bcmgenet: probe of bcmgenet.1 failed with error -5
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
__clk_enable: usb [1]
bcm40nm_pm_usb_enable 00
ehci-brcm ehci-brcm.0: Broadcom STB EHCI
ehci-brcm ehci-brcm.0: new USB bus registered, assigned bus number 1
ehci-brcm ehci-brcm.0: irq 56, io mem 0x10480300
ehci-brcm ehci-brcm.0: USB 0.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci-brcm ehci-brcm.1: Broadcom STB EHCI
ehci-brcm ehci-brcm.1: new USB bus registered, assigned bus number 2
ehci-brcm ehci-brcm.1: irq 57, io mem 0x10480500
ehci-brcm ehci-brcm.1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
ehci-brcm ehci-brcm.2: Broadcom STB EHCI
ehci-brcm ehci-brcm.2: new USB bus registered, assigned bus number 3
ehci-brcm ehci-brcm.2: irq 61, io mem 0x10490300
ehci-brcm ehci-brcm.2: USB 0.0 started, EHCI 1.00
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 1 port detected
ehci-brcm ehci-brcm.3: Broadcom STB EHCI
ehci-brcm ehci-brcm.3: new USB bus registered, assigned bus number 4
ehci-brcm ehci-brcm.3: irq 62, io mem 0x10490500
ehci-brcm ehci-brcm.3: USB 0.0 started, EHCI 1.00
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ata2: SATA link down (SStatus 0 SControl 300)
ohci-brcm ohci-brcm.0: Broadcom STB OHCI
ohci-brcm ohci-brcm.0: new USB bus registered, assigned bus number 5
ohci-brcm ohci-brcm.0: irq 58, io mem 0x10480400
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 1 port detected
ohci-brcm ohci-brcm.1: Broadcom STB OHCI
ohci-brcm ohci-brcm.1: new USB bus registered, assigned bus number 6
ohci-brcm ohci-brcm.1: irq 59, io mem 0x10480600
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 1 port detected
ohci-brcm ohci-brcm.2: Broadcom STB OHCI
ohci-brcm ohci-brcm.2: new USB bus registered, assigned bus number 7
ohci-brcm ohci-brcm.2: irq 63, io mem 0x10490400
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 1 port detected
ohci-brcm ohci-brcm.3: Broadcom STB OHCI
ohci-brcm ohci-brcm.3: new USB bus registered, assigned bus number 8
ohci-brcm ohci-brcm.3: irq 64, io mem 0x10490600
hub 8-0:1.0: USB hub found
hub 8-0:1.0: 1 port detected
usbcore: registered new interface driver usb-storage
mousedev: PS/2 mouse device common for all mice
i2c /dev entries driver
Success! Registering the characther device success with 0
blackhole initialised
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
sdhci-pltfm: SDHCI platform and OF driver helper
hidraw: raw HID events driver (C) Jiri Kosina
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP: cubic registered
NET: Registered protocol family 17
Key type dns_resolver registered
PM: CP0 COUNT/COMPARE frequency does not depend on divisor
EBI CS0: setting up NAND flash (primary)
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix H27U4G8F2DTR-BC)
NAND device: 512MiB, SLC, page size: 2048, OOB size: 64
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix H27U4G8F2DTR-BC)
NAND device: 512MiB, SLC, page size: 2048, OOB size: 64
brcmnand brcmnand.0: 512MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, Hamming ECC
Bad block table found at page 262080, version 0x01
Bad block table found at page 262016, version 0x01
nand_read_bbt: bad block at 0x000005b20000
Creating 4 MTD partitions on "brcmnand.0":
0x000001f00000-0x000020000000 : "rootfs"
0x000001f00000-0x000020000000 : "rootfs(redundant)"
0x000000200000-0x000000900000 : "kernel"
0x000000900000-0x000000a00000 : "mac"
UBI: attaching mtd0 to ubi0
usb 6-1: new full-speed USB device number 2 using ohci-brcm
random: nonblocking pool is initialized
usb 6-1: device descriptor read/64, error -62
usb 6-1: device descriptor read/64, error -62
usb 6-1: new full-speed USB device number 3 using ohci-brcm
usb 6-1: device descriptor read/64, error -62
usb 6-1: device descriptor read/64, error -62
UBI: scanning is finished
UBI: attached mtd0 (name "rootfs", size 481 MiB) to ubi0
UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
UBI: VID header offset: 2048 (aligned 2048), data offset: 4096
UBI: good PEBs: 3839, bad PEBs: 9, corrupted PEBs: 0
UBI: user volume: 1, internal volumes: 1, max. volumes count: 128
UBI: max/mean erase counter: 10/5, WL threshold: 4096, image sequence number: 1453135829
UBI: available PEBs: 0, total reserved PEBs: 3839, PEBs reserved for bad PEB handling: 71
UBI: background thread "ubi_bgt0d" started, PID 55
ALSA device list:
No soundcards found.
UBIFS: parse sync
UBIFS: background thread "ubifs_bgt0_0" started, PID 58
usb 6-1: new full-speed USB device number 4 using ohci-brcm
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
UBIFS: FS size: 476540928 bytes (454 MiB, 3753 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs)
UBIFS: reserved for root: 0 bytes (0 KiB)
UBIFS: media format: w4/r0 (latest is w4/r0), UUID 3B7DDD43-05C2-48D0-A8EA-796993B506D8, small LPT model
VFS: Mounted root (ubifs filesystem) on device 0:12.
devtmpfs: mounted
Freeing unused kernel memory: 248K (80762000 - 807a0000)
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
usb 6-1: device not accepting address 4, error -62
usb 6-1: new full-speed USB device number 5 using ohci-brcm
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
usb 6-1: device not accepting address 5, error -62
hub 6-0:1.0: unable to enumerate USB device on port 1
udevd[132]: starting version 182
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
procmk_init
bcm_event: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (_vuplus_solose_)
bcm7241: hotplug_callback():
Hotplug - status.connected 1:0:0
bcm7241: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
[GPIO]Default
bcm7241: hotplug_callback():
Hotplug - status.connected 1:1:2
brcm_demux_init: $Id: bcm_demux.c,v 0.7 $
[MPVR]: >> misc_pvr_init
[VID]: 6bcm7335_video_init
[AUD]: 6bcm7335_audio_init
BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (Vuplus FE)...
BRCM brcm_dvb0: DVB: registering adapter 0 frontend 0 (Vuplus FE)...
bcm7241: bcm7335_frontend_init(): vtuner1 : 3
BKNI_P_GetTrackAllocEntry_resize: resizing from 5376->8704
BKNI_Malloc(linuxkernel) top users:
blocks, bytes, filename:line
1024, 176128, portinginterface/hsm/src/common/bhsm.c:500
729, 162684, BSEAV/lib/utils/balloc.c:31
KSEG1 : 0x80000000
input: dreambox advanced remote control (native) as /devices/virtual/input/input0
[LCD]: registered
0:0
[CI]: registered ci0
[CI]: CI interface initialised
[DFP]: registered dbox fp
[DFP]: Scart 4710 is found 4
[SC]: registered sci0
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1 0
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0 0
__clk_enable: network [1]
bcm7429_pm_network_enable 00
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
bcmgenet bcmgenet.0 eth0: link up, 100 Mbps, full duplex
bcmgenet bcmgenet.0 eth0: link down
NET: Registered protocol family 10
bcmgenet bcmgenet.0 eth0: link up, 100 Mbps, full duplex
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1 0
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0 0
UBI error: ubi_open_volume: cannot open device 0, volume 0, error -16
CIFS: Unknown mount option "r"
fuse init (API version 7.22)
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -855302672
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -210, right volume -210
[AUD]: AUDIO_SET_MIXER -855302672
[AUD]: AUDIO_SET_MIXER : amixl 19, amixr 19
[AUD]: AUDIO_SET_MIXER : next left volume -210, right volume -210
[AUD]: AUDIO_SET_MIXER : next left volume -1567, right volume -1567