Hi everyone,
I´m having problems trying to install these usb sticks in a Vu+ Duo. The image i´m using is bh 1.7.4.
Hauppauge stick worked well alone, but now I´m trying to add the Sundtek stick and I can´t make it work.
usb devices:
lsmod:
dmesg:
I don´t understand it much, but I see that Sundtek driver= (none) and I think this could be the problem. I have the sundtek control center plugin installed and the drivers of the stick are updated to Aug.3.2012 by this plugin.
Any help?
Thanks in advance.
I´m having problems trying to install these usb sticks in a Vu+ Duo. The image i´m using is bh 1.7.4.
Hauppauge stick worked well alone, but now I´m trying to add the Sundtek stick and I can´t make it work.
usb devices:
Code:
root@bm750:~# cat /proc/bus/usb/devices
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.01
S: Manufacturer=Linux 3.1.1 ohci_hcd
S: Product=Broadcom STB OHCI
S: SerialNumber=ohci_hcd
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.01
S: Manufacturer=Linux 3.1.1 ohci_hcd
S: Product=Broadcom STB OHCI
S: SerialNumber=ohci_hcd
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.01
S: Manufacturer=Linux 3.1.1 ehci_hcd
S: Product=Broadcom STB EHCI
S: SerialNumber=ehci_hcd
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 1/800 us ( 0%), #Int= 3, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.01
S: Manufacturer=Linux 3.1.1 ehci_hcd
S: Product=Broadcom STB EHCI
S: SerialNumber=ehci_hcd
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0bda ProdID=8178 Rev= 2.00
S: Manufacturer=Realtek
S: Product=802.11n WLAN Adapter
S: SerialNumber=00e04c000001
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=ff Prot=ff Driver=rtl8192cu
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=84(I) Atr=03(Int.) MxPS= 64 Ivl=125us
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=480 MxCh= 4
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=058f ProdID=6254 Rev= 1.00
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=01 Lev=02 Prnt=03 Port=00 Cnt=01 Dev#= 4 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=2040 ProdID=c000 Rev= 0.01
S: Manufacturer=Hauppauge Computer Works
S: Product=WinTV MiniStick
S: SerialNumber=4034525315
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=smsusb
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=01 Lev=02 Prnt=03 Port=01 Cnt=02 Dev#= 5 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=eb1a ProdID=51b2 Rev= 1.00
S: Manufacturer=Sundtek
S: Product=MediaTV Digital Home
S: SerialNumber=U120622044451
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=01(Isoc) MxPS= 0 Ivl=125us
I: If#= 0 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E: Ad=84(I) Atr=01(Isoc) MxPS= 940 Ivl=125us
T: Bus=01 Lev=02 Prnt=03 Port=02 Cnt=03 Dev#= 6 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=046d ProdID=c52b Rev=12.01
S: Manufacturer=Logitech
S: Product=USB Receiver
C:* #Ifs= 3 Cfg#= 1 Atr=a0 MxPwr= 98mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=8ms
I:* If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=2ms
I:* If#= 2 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
E: Ad=83(I) Atr=03(Int.) MxPS= 32 Ivl=2ms
T: Bus=01 Lev=02 Prnt=03 Port=03 Cnt=04 Dev#= 7 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=058f ProdID=6366 Rev= 1.00
S: Manufacturer=Generic
S: Product=Mass Storage Device
S: SerialNumber=058F63666471
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Code:
root@bm750:~# lsmod
Tainted: P
nfsd 100029 6 - Live 0xc14f3000
exportfs 3994 1 nfsd, Live 0xc14c9000
ext2 56603 0 - Live 0xc14b1000
smsdvb 12173 2 - Live 0xc1466000
bh_dvb_core 91481 1 smsdvb, Live 0xc143f000
smsusb 8236 0 - Live 0xc13fd000
smsmdtv 24228 2 smsdvb,smsusb, Live 0xc13ec000
bh_rc_core 14686 2 smsmdtv, Live 0xc13d7000
uas 7735 0 - Live 0xc13c9000
brcmfb 1127 2 - Live 0xc126b000
dvb_bcm7335 4932784 45 brcmfb, Live 0xc09c3000 (P)
procmk 1397 1 dvb_bcm7335, Live 0xc0451000
8192cu 544125 0 - Live 0xc0377000
ipv6 342577 10 - Live 0xc0257000
Code:
Set RF Chip ID to RF_6052 and RF type to 2.
IQK:Start!!!
Path A IQK Success!!
Path B IQK Success!!
Path A IQK Success!!
Path B IQK Success!!
IQK: final_candidate is 0
IQK: RegE94=ff RegE9C=3 RegEA4=f6 RegEAC=9 RegEB4=102 RegEBC=b RegEC4=fa RegECC=2
Path A IQ Calibration Success !
Path B IQ Calibration Success !
pdmpriv->TxPowerTrackControl = 1
MAC Address from REG_MACID = 80:1f:02:27:de:90
rtl8192cu_hal_init in 646ms
MAC Address = 80:1f:02:27:de:90
-871x_drv - drv_open, bup=1
ADDRCONF(NETDEV_UP): wlan0: link is not ready
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
set_mode = IW_MODE_INFRA
[rtw_wx_set_pmkid] IW_PMKSA_FLUSH!
survey done event(3)
wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
set_mode = IW_MODE_INFRA
wpa_ie(length:22):
0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02
0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
0x00 0x0f 0xac 0x02 0x00 0x00 0xea 0x86
=>rtw_wx_set_essid
ssid=ddcc1e, len=6
Set SSID under fw_state=0x00000008
[by_bssid:0][assoc_ssid:ddcc1e][to_roaming:0] new candidate: ddcc1e(e0:69:95:6a:74:b9) rssi:-42
rtw_select_and_join_from_scanned_queue: candidate: ddcc1e(e0:69:95:6a:74:b9)
rtw_restructure_ht_ie IEEE80211_HT_CAP_MAX_AMSDU is set
link to Broadcom AP
tw_wx_set_essid, ret 0
Set BSSID under fw_state=0x00000088
link to Broadcom AP
link_timer_hdl: auth timeout and try again
link_timer_hdl: auth timeout and try again
report_join_res(-1)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
svc: failed to register lockdv1 RPC service (errno 124).
DVB: registering adapter 0 frontend 0 (Siano Mobile Digital MDTV Receiver)...
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
OnAuthClient
survey done event(9)
wpa_set_auth_algs, AUTH_ALG_OPEN_SYSTEM
set_mode = IW_MODE_INFRA
wpa_ie(length:22):
0x30 0x14 0x01 0x00 0x00 0x0f 0xac 0x02
0x01 0x00 0x00 0x0f 0xac 0x04 0x01 0x00
0x00 0x0f 0xac 0x02 0x00 0x00 0x00 0x00
=>rtw_wx_set_essid
ssid=ddcc1e, len=6
Set SSID under fw_state=0x00000008
[by_bssid:0][assoc_ssid:ddcc1e][to_roaming:0] new candidate: ddcc1e(e0:69:95:6a:74:b9) rssi:-42
rtw_select_and_join_from_scanned_queue: candidate: ddcc1e(e0:69:95:6a:74:b9)
rtw_restructure_ht_ie IEEE80211_HT_CAP_MAX_AMSDU is set
link to Broadcom AP
tw_wx_set_essid, ret 0
Set BSSID under fw_state=0x00000088
link to Broadcom AP
OnAuthClient
network.SupportedRates[0]=82
network.SupportedRates[1]=84
network.SupportedRates[2]=8B
network.SupportedRates[3]=96
network.SupportedRates[4]=24
network.SupportedRates[5]=30
network.SupportedRates[6]=48
network.SupportedRates[7]=6C
network.SupportedRates[8]=0C
network.SupportedRates[9]=12
network.SupportedRates[10]=18
network.SupportedRates[11]=60
bssrate_len = 12
declare supporting RX STBC
OnAssocRsp
report_join_res(3)
rtw_joinbss_update_network
+rtw_update_ht_cap()
rtw_joinbss_update_stainfo
HW_VAR_BASIC_RATE: BrateCfg(0x15d)
ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
WMM(0): 0, a42b
WMM(1): 0, a44f
WMM(2): 0, 5e4322
WMM(3): 0, 2f3222
[HW_VAR_ACM_CTRL] Write 0x0
HTOnAssocRsp
update raid entry, mask=0xfffffff, arg=0xa0
rtl8192c_set_FwJoinBssReport_cmd mstatus(1)
SetFwRsvdPagePkt
Set RSVD page location to Fw.
=>mlmeext_joinbss_event_callback
OnAction_back
OnAction_back, action=0
issue_action_BA, category=3, action=1, status=0
~~~~stastakey:unicastkey
~~~~stastakey:groupkey
==> rtw_set_key algorithm(2),keyid(2),key_mask(4)
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
wlan0: no IPv6 routers present
[CI]:ci_dev_open
[CI]:Opening A GPIO's for 7335 platform
[CI]:Opening A GPIO's for 7335 platform....done
[CI]:entering.. A NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card insertion status changed
[CI]:Opening B GPIO's for 7335 platform
[CI]:Opening B GPIO's for 7335 platform....done
[CI]:entering.. B NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card B insertion status changed
[CI]: CI interface initialised
[CI]:ci1_dev_open
[CI]:NEXUS_Remux_Start
[CI]:>>close_mpod tuner:0
[CI]:remux stop
[CI]:get_remux_startcnt() count : 1
[CI]:get_remux_startcnt() count : 1
[CI]:>>close_mpod tuner:1
[CI]:remux stop
[CI]:get_remux_startcnt() count : 0
[CI]:get_remux_startcnt() count : 0
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -2035491344
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -200, right volume -200
[AUD]: AUDIO_SET_MIXER -2035491344
[AUD]: AUDIO_SET_MIXER : amixl 35, amixr 35
[AUD]: AUDIO_SET_MIXER : next left volume -200, right volume -200
[AUD]: AUDIO_SET_MIXER : next left volume -2700, right volume -2700
FE tune
dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
[AUD]: AUDIO_SET_BYPASS_MODE 1
[AUD]: proc_get_ac3 0 audio_passthrough_spdif : 0
[AUD]: AUDIO_PAUSE 1
[AUD]: AUDIO_PLAY 1 decoder start : 0
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_FREEZE 1 0
[VID]: VIDEO_PLAY 1 2 2
[VID]: VIDEO_SLOWMOTION 0 1
[VID]: VIDEO_FAST_FORWARD 0 1
[VID]: VIDEO_CONTINUE 1 1
[AUD]: AUDIO_CONTINUE 1 1 audio pid_hndl : 0xc0dfa02c
[AUD]: setting mute : 0
[AUD]: AUDIO_CHANNEL_SELECT 0
dvb_demux_feed_del: feed not in list (type=0 state=0 pid=ffff)
[VID]: VIDEO_SLOWMOTION 0 1
[VID]: VIDEO_FAST_FORWARD 0 1
[VID]: VIDEO_CONTINUE 1 1
[AUD]: AUDIO_CONTINUE 1 1 audio pid_hndl : 0xc0dfa02c
[AUD]: setting mute : 0
out of order segment: rcv_next E6A52B2B seq E6A52B54 - E6A52B55
ofo requeuing : rcv_next E6A52B54 seq E6A52B54 - E6A52B55
rtw_issue_addbareq_cmd, p=0
issue_action_BA, category=3, action=0, status=0
BA_starting_seqctrl = 442 for TID=0
OnAction_back
OnAction_back, action=1
agg_enable for TID=0
OnAction_back
OnAction_back, action=1
agg_enable for TID=0I don´t understand it much, but I see that Sundtek driver= (none) and I think this could be the problem. I have the sundtek control center plugin installed and the drivers of the stick are updated to Aug.3.2012 by this plugin.
Any help?
Thanks in advance.
