sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
brcmnand_read_id: CS0: dev_id=ecf10095
After: NandSelect=40000101, nandConfig=15142200
Found NAND flash on Chip Select 0, chipSize=128MB, usable size=128MB, base=0
brcmnand_scan: B4 nand_select = 40000101
brcmnand_scan: After nand_select = 40000101
page_shift=11, bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17
Brcm NAND controller version = 3.2 NAND flash size 128MB @18000000
ECC layout=brcmnand_oob_bch4_4k
brcmnand_scan: mtd->oobsize=64
brcmnand_scan: oobavail=50, eccsize=512, writesize=2048
brcmnand_scan, eccsize=512, writesize=2048, eccsteps=4, ecclevel=15, eccbytes=3
-->brcmnand_default_bbt
brcmnand_default_bbt: bbt_td = bbt_main_descr
Bad block table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0
Bad block table 1tbB found at page 0000ff80, version 0x01 for chip on CS0
nand_read_bbt: Bad block at 0x02f20000
nand_read_bbt: Bad block at 0x062a0000
Creating 8 MTD partitions on "brcmnand.0":
0x000000000000-0x000007200000 : "rootfs"
0x000007200000-0x000007600000 : "kernel"
0x000007600000-0x000007a00000 : "boot"
0x000007a00000-0x000007c00000 : "splash"
0x000007c00000-0x000007d00000 : "cfe"
0x000007d00000-0x000007d80000 : "mac"
0x000007d80000-0x000007e00000 : "env"
0x000007e00000-0x000007f00000 : "nvm"
sda: sda1
UBI: attaching mtd0 to ubi0
sd 0:0:0:0: [sda] Attached SCSI disk
UBI: physical eraseblock size: 131072 bytes (128 KiB)
UBI: logical eraseblock size: 126976 bytes
UBI: smallest flash I/O unit: 2048
UBI: VID header offset: 2048 (aligned 2048)
UBI: data offset: 4096
ata2: SATA link down (SStatus 4 SControl 300)
UBI: max. sequence number: 1050
UBI: attached mtd0 to ubi0
UBI: MTD device name: "rootfs"
UBI: MTD device size: 114 MiB
UBI: number of good PEBs: 910
UBI: number of bad PEBs: 2
UBI: number of corrupted PEBs: 0
UBI: max. allowed volumes: 128
UBI: wear-leveling threshold: 4096
UBI: number of internal volumes: 1
UBI: number of user volumes: 1
UBI: available PEBs: 0
UBI: total number of reserved PEBs: 910
UBI: number of PEBs reserved for bad PEB handling: 9
UBI: max/mean erase counter: 7/1
UBI: image sequence number: 40675335
UBI: background thread "ubi_bgt0d" started, PID 47
UBIFS: parse sync
UBIFS: mounted UBI device 0, volume 0, name "rootfs"
UBIFS: file system size: 112500736 bytes (109864 KiB, 107 MiB, 886 LEBs)
UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
UBIFS: media format: w4/r0 (latest is w4/r0)
UBIFS: default compressor: lzo
UBIFS: reserved for root: 0 bytes (0 KiB)
VFS: Mounted root (ubifs filesystem) on device 0:12.
Freeing unused kernel memory: 244k freed
NET: Registered protocol family 10
rtw driver version=v3.4.4_xxxx.20120730
Build at: Dec 3 2012 17:11:41
usbcore: registered new interface driver rtl8192cu
procmk_init
dvb_bcm7413: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
DVB: registering new adapter (vuuno)
enable MII = 0
NEXUS_Frontend_GetUserParameters 0 0
bcm7413: hotplug_callback():
Hotplug - status.connected 1
bcm7413: hotplug_callback():
Hotplug - connecting HDMI to display 0xe
[GPIO]Default
[GPIO]RST Default
[GPIO]fpga secu
[GP]:brcm_pwm_init
brcm_demux_init: $Id: bcm7335_demux.c,v 0.6 $
[VID]: <6>bcm7335_video_init
[AUD]: <6>bcm7335_audio_init
DVB: registering adapter 0 frontend 0 (Vuplus FE)...
bcm7413: bcm7335_frontend_init(): vtuner1 : 2
[MPVR]: >> misc_pvr_init
input: dreambox advanced remote control (native) as /devices/virtual/input/input 0
[LCD]: registered
[CI]:0 1
[CI]: registered ci0 0
[CI]: registered ci1 0
[DFP]: registered dbox fp
[DFP]: Scart 9597 is found 4
[SC]: registered sci0
[SC]: registered sci1
system_time_set wakeup mode get
system_time_set wakeup mode get 0xc4
fpga update driver loaded
udevd (105): /proc/105/oom_adj is deprecated, please use /proc/105/oom_score_adj instead.
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda1): using internal journal
EXT3-fs (sda1): mounted filesystem with writeback data mode
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
svc: failed to register lockdv1 RPC service (errno 124).
[VID]: VIDEO_SET_STREAMTYPE 0
[VID]: VIDEO_SELECT_SOURCE 1
[VID]: VIDEO_PLAY 1 2 0
[VID]: VIDEO_CONTINUE 1 1
[VID]: VIDEO_CLEAR_BUFFER 1 1 0
[VID]: VIDEO_STOP 0 1
[VID]: VIDEO_SELECT_SOURCE 0
[LCD]: unknown cmd 0x1015
[CI]:ci_dev_open
[CI]:entering.. A NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card insertion status changed
[CI]:entering.. B NEXUS_DvbCi_Open
[CI]:NEXUS_DvbCi_Open done..
[CI]:Installing callbacks
[CI]:Forcing card check
[CI]:Card B insertion status changed
[CI]: CI interface initialised
[CI]:ci1_dev_open
[AUD]: AUDIO_SET_MUTE 0
[AUD]: AUDIO_SET_MIXER -839115280
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume 0, right volume 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER -839115280
[AUD]: AUDIO_SET_MIXER : amixl 0, amixr 0
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
[AUD]: AUDIO_SET_MIXER : next left volume -70, right volume -70
FE tune c
[AUD]: AUDIO_SET_BYPASS_MODE 0
[AUD]: AC3 proc_get_ac3 0 audio_passthrough_spdif : 0
[AUD]: AUDIO_PAUSE 1
[AUD]: AUDIO_PLAY 1 decoder start : 0
[VID]: VIDEO_SET_STREAMTYPE 1
[VID]: VIDEO_FREEZE 1 0
[VID]: VIDEO_PLAY 1 5 2
[VID]: VIDEO_SLOWMOTION 0 1
[VID]: VIDEO_FAST_FORWARD 0 1
[VID]: VIDEO_CONTINUE 1 1
[AUD]: AUDIO_CONTINUE 1 1 audio pid_hndl : 0xe0db4f54
[AUD]: setting mute : 0
[AUD]: AUDIO_CHANNEL_SELECT 0
usb 1-2: new high speed USB device number 2 using ehci-brcm
Linux video capture interface: v2.00
WARNING: You are using an experimental version of the media stack.
As the driver is backported to an older kernel, it doesn't offer
enough quality for its usage in production.
Use it with care.
Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
Custom Black Hole build
em28xx: New device PCTV Systems PCTV 520e @ 480 Mbps (2013:0251, interface 0, cl ass 0)
em28xx: Audio Vendor Class interface 0 found
em28xx: Video interface 0 found
em28xx: DVB interface 0 found
em28xx #0: chip ID is em2884
em28xx #0: Identified as PCTV QuatroStick nano (520e) (card=86)
em28xx #0: Config register raw data: 0x24
em28xx #0: I2S Audio (3 sample rates)
em28xx #0: No AC97 audio processor
em28xx #0: v4l2 driver version 0.1.3
em28xx #0: V4L2 video device registered as video0
usbcore: registered new interface driver em28xx
WARNING: You are using an experimental version of the media stack.
As the driver is backported to an older kernel, it doesn't offer
enough quality for its usage in production.
Use it with care.
Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
Custom Black Hole build
drxk: frontend initialized.
drxk: status = 0x639260d9
drxk: detected a drx-3926k, spin A3, xtal 20.250 MHz
tda18271 4-0060: creating new instance
DRXK driver version 0.9.4300
tda18271_read_regs: [4-0060|M] ERROR: i2c_transfer returned: -19
Unknown device (16) detected @ 4-0060, device not supported.
tda18271_attach: [4-0060|M] error -22 on line 1274
tda18271 4-0060: destroying instance
Em28xx: Initialized (Em28xx dvb Extension) extension
WARNING: You are using an experimental version of the media stack.
As the driver is backported to an older kernel, it doesn't offer
enough quality for its usage in production.
Use it with care.
Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
Custom Black Hole build
IR keymap rc-pinnacle-pctv-hd not found
Registered IR keymap rc-empty
input: em28xx IR (em28xx #0) as /devices/platform/ehci-brcm.0/usb1/1-2/bh-rc/rc0 /input1
rc0: em28xx IR (em28xx #0) as /devices/platform/ehci-brcm.0/usb1/1-2/bh-rc/rc0
Em28xx: Initialized (Em28xx Input Extension) extension
root@vuuno:~#
