Hmmm... You must to start testing of all elements of Your installation.
1. LNB (maybe is in conflict with vu+ tuner)
2. Cable connection (cable and F connectors)
3. Make a one fresh installation of BH 1.6.4
4. Set up Your settings and reboot.
You must to work step by step to find a problems. I think that problem is in installation not in box.
Dzoni,
Thank you for your reply and advice. I walked thru these steps many times already. The LNB can't be defect as the SelfSat Dish (LNB integrated) is just 7 months old and was working correctly with my previous decoder. Same with the cable, it's renewed 4 months ago for Belden H126 Duobond high end cable (not more than 10mtr).
I re-flashed the BH 1.6.4 image I think four or five times now including a fresh set up of the satsettings (so no copying from the previous installation). During these re-flashes I also tried different satsetting files to be found in this forum. So in total I tried:
- fresh installation with USALS configuration
- fresh installation with DiSEqC1.2 using prestored sat positions of the rotor table
- fresh installation with DiSEqC1.2 pointing the sat to the different sat by myself
- fresh installation with USALS configuration and satsettings from this forum
- fresh installation with DiSEqC1.2 configuration and satsettings form this forum
With my "old" Homecast device all different configurations worked without problem, USALS, DiSEqC1.2 and "Motor".
If I don't put the device in Standby, there is no issue, it starts AFTER Standby. I could left the device turned on, but I think it won't be healthy for the box life expectations
I managed to obtain the crashlog as of 22/07/11. Maybe the problem is to be found in here? I have no idea what to read out of this except:
RemovePopup, id = ZapError
[eDVBCAService] remove channel 0x1a8f420
[eDVBCAService] write leave transponder failed!!
[eDVBLocalTimerHandler] remove channel 0x1a8f420
[eEPGCache] remove channel 0x1a8f420
[EPGC] abort caching events !!
allocate channel.. 0c99:0003
[eDVBCAService] new channel 0x1a8f420!
(0)tune
Entry for 23,5? not in Rotor Table found... i try gotoXX?
siteLatitude = 52.007999, siteLongitude = 4.746000, 23.500000 degrees
PolarmountHourAngle=159.368829
RotorCmd = e14a
RotorCmd e14a, lastRotorCmd e14a
prepare_sat System 1 Freq 12187000 Pol 0 SR 27500000 INV 2 FEC 4 orbpos 235 system 1 modulation 1 pilot 2, rolloff 0
tuning to 1587 mhz
OURSTATE: tuning
allocate Channel: res 0
But what is this referring to? Which Rotor Table does the device mean? If I remember correctly this log was while using USALS settings.
Thanks in advance....
+- 1/2 TID 4e
sdt update done!
[AutoRes] determineContent
[AutoRes] switch deinterlacer mode to auto
[AutoRes] new content is 1920x1080i25
[AutoRes] determined videomode 1080i
++ 2/2 TID 4e
done!
doing version filtering
0012: 4e 51 d6 2f 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
It's now Fri Jul 22 00:36:27 2011
[timer.py] next activation: 1311287887 (in 99997 ms)
It's now Fri Jul 22 00:36:27 2011
[timer.py] next activation: 1311287887 (in 99995 ms)
[EPGC] start caching events(1311287787)
[eDVBLocalTimerHandler] diff is 1
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] update RTC
[eDVBLocalTimerHandler] time update to 00:36:29
[eDVBLocalTimerHandler] m_time_difference is 1
[eDVBLocalTimerHandler] set Linux Time
[EPGC] start cleanloop
[EPGC] stop cleanloop
[EPGC] 584772 bytes for cache used
playing 1:0:19:5217:C99:3:EB0000:0:0:0:
[eDVBCAService] free slot 0 demux 0 for service 1:0:19:51D6:C96:3:EB0000:0:0:0:
[eDVBCAService] free service 1:0:19:51D6:C96:3:EB0000:0:0:0:
[eDVBCIInterfaces] remove last pmt handler for service 1:0:19:51D6:C96:3:EB0000:0:0:0: send empty capmt
eDVBCIInterfaces->setInputSource(0, 0)
(3) slot 1 usecount is now 0
decoder state: play, vpid=-1, apid=-1
DEMUX_STOP - pcr - ok
DEMUX_STOP - video - ok
VIDEO_STOP - ok
AUDIO_STOP - ok
DEMUX_STOP - audio - ok
AUDIO_CONTINUE - ok
DEMUX_STOP - ttx - ok
start release channel timer
not pauseable.
RemovePopup, id = ZapError
[eDVBCAService] remove channel 0x1a8f420
[eDVBCAService] write leave transponder failed!!
[eDVBLocalTimerHandler] remove channel 0x1a8f420
[eEPGCache] remove channel 0x1a8f420
[EPGC] abort caching events !!
allocate channel.. 0c99:0003
[eDVBCAService] new channel 0x1a8f420!
(0)tune
Entry for 23,5? not in Rotor Table found... i try gotoXX?
siteLatitude = 52.007999, siteLongitude = 4.746000, 23.500000 degrees
PolarmountHourAngle=159.368829
RotorCmd = e14a
RotorCmd e14a, lastRotorCmd e14a
prepare_sat System 1 Freq 12187000 Pol 0 SR 27500000 INV 2 FEC 4 orbpos 235 system 1 modulation 1 pilot 2, rolloff 0
tuning to 1587 mhz
OURSTATE: tuning
allocate Channel: res 0
[eDVBCIInterfaces] addPMTHandler 1:0:19:5217:C99:3:EB0000:0:0:0:
caid '0100' is in caid list of slot 1... so use it
(1)CISlot 1, usecount now 1
eDVBCIInterfaces->setInputSource(0, 5)
CI Slot 1 setSource(0)
[eDVBCIInterfaces] gotPMT
allocate demux
resolve: resolve ${sysconfdir}/scan_tp_valid_check.py
resolve: -> /etc/scan_tp_valid_check.py
[SEC] set static current limiting
[SEC] setVoltage 2
[SEC] sleep 10ms
set sequence pos 3
[SEC] update current switch params
[SEC] startTuneTimeout 5000
[SEC] setFrontend 1
setting frontend 0
[SEC] sleep 500ms
(0)fe event: status 0, inversion off, m_tuning 1
BlackHoleapi: popclose,
(0)fe event: status 1f, inversion on, m_tuning 2
OURSTATE: ok
[eDVBCAService] channel 0x1a8f420 running
[eDVBLocalTimerHandler] channel 0x1a8f420 running
no version filtering
0014: 70 00 00 00 00 00
mask: fc 00 00 00 00 00
mode: 00 00 00 00 00 00
[eEPGCache] channel 0x1a8f420 running
stop release channel timer
no version filtering
0012: 4e 52 17 00 00 00
mask: ff ff ff 00 00 00
mode: 00 00 00 00 00 00
ok ... now we start!!
no version filtering
0000: 00 00 00 00 00 00
mask: ff 00 00 00 00 00
mode: 00 00 00 00 00 00
eventNewProgramInfo 0 0
have 1 video stream(s) (0201), and 1 audio stream(s) (0065), and the pcr pid is 0201, and the text pid is 0021
allocate demux
disable teletext subtitles
decoder state: play, vpid=513, apid=101
DMX_SET_PES_FILTER(0x201) - pcr - ok
DEMUX_START - pcr - ok
DMX_SET_PES_FILTER(0x65) - audio - ok
DEMUX_START - audio - ok
AUDIO_SET_BYPASS(0) - ok
AUDIO_PAUSE - ok
AUDIO_PLAY - ok
Video Device: /dev/dvb/adapter0/video0
demux device: /dev/dvb/adapter0/demux0
VIDEO_SET_STREAMTYPE 1 - ok
DMX_SET_PES_FILTER(0x201) - video - ok
DEMUX_START - video - ok
VIDEO_FREEZE - ok
VIDEO_PLAY - [EPGC] next update in 2 sec
ok
DMX_SET_PES_FILTER(0x21) - ttx - ok
DEMUX_START - ttx - ok
VIDEO_SLOWMOTION(0) - ok
VIDEO_FAST_FORWARD(0) - ok
VIDEO_CONTINUE - ok
AUDIO_CONTINUE - ok
not pauseable.
[AutoRes] service changed
+ 1/1 TID 00
done!
PATready
use pmtpid 0a9b for service_id 5217
no version filtering
0a9b: 02 52 17 00 00 00
mask: ff ff ff 00 00 00
mode: 00 00 00 00 00 00
doing version filtering
0000: 00 00 00 05 00 00
mask: ff 00 00 3f 00 00
mode: 00 00 00 3e 00 00
[SEC] set dynamic current limiting
+ 1/1 TID 02
done!
eventNewProgramInfo 0 0
have 1 video stream(s) (0201), and 1 audio stream(s) (0065), and the pcr pid is 0201, and the text pid is 0021
decoder state: play, vpid=513, apid=101
[eDVBCAService] new service 1:0:19:5217:C99:3:EB0000:0:0:0:
[eDVBCAService] add demux 0 to slot 0 service 1:0:19:5217:C99:3:EB0000:0:0:0:
caid '0100' is in caid list of slot 1... so use it
[eDVBCIInterfaces] gotPMT
demux 0 mask 01 prevhash 00000000
doing version filtering
0a9b: 02 52 17 11 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
action -> InfobarShowHideActions toggleShow
+- 1/2 TID 4e
sdt update done!
[AutoRes] determineContent
[AutoRes] switch deinterlacer mode to auto
[AutoRes] new content is 1920x1080i25
[AutoRes] determined videomode 1080i
++ 2/2 TID 4e
done!
doing version filtering
0012: 4e 52 17 17 00 00
mask: ff ff ff 3f 00 00
mode: 00 00 00 3e 00 00
[EPGC] start caching events(1311287794)
[eDVBLocalTimerHandler] diff is 0
[eDVBLocalTimerHandler] diff < 120 .. use Transponder Time
[eDVBLocalTimerHandler] not changed
[EPGC] abort non avail schedule other reading
[EPGC] abort non avail viasat reading
[EPGC] abort non avail mhw reading
nr_read 120 nr_write 421
sum 541 prev_sum 108
hdd was accessed since previous check!
[IDLE] 0 600 False
[EPGC] nownext finished(1311287809)
no ancillary data in audio stream... abort radiotext pes parser
action -> InfobarInstantRecord instantRecord
self.recording: []
action -> WizardActions back
pre:
[]
action -> InfobarSubserviceSelectionActions DeliteGpshow
allocating new converter!
action -> WizardActions down
unknown action WizardActions/down! typo in keymap?
action -> WizardActions down
unknown action WizardActions/down! typo in keymap?
action -> WizardActions ok
Looking for embedded skin
screen cleanup!
screen cleanup!
action -> ColorActions yellow
Looking for embedded skin
Traceback (most recent call last):
File "/usr/lib/enigma2/python/Plugins/Extensions/FanControl2/plugin.py", line 325, in DoTest
setVoltage(self.id,SaveAktVLT)
File "/usr/lib/enigma2/python/Plugins/Extensions/FanControl2/plugin.py", line 115, in setVoltage
f = open("/proc/stb/fp/fan_vlt", "w")
IOError: [Errno 2] No such file or directory: '/proc/stb/fp/fan_vlt'
(PyObject_CallObject(<bound method FanControl2Test.DoTest of <class 'Plugins.Extensions.FanControl2.plugin.FanControl2Test'>>,()) failed)
getResolvedKey config.plugins.crashlogautosubmit.sendAnonCrashlog failed !! (Typo??)
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
getResolvedKey config.plugins.crashlogautosubmit.addNetwork failed !! (Typo??)
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
getResolvedKey config.plugins.crashlogautosubmit.addWlan failed !! (Typo??)
resolve: resolve ${sysconfdir}/enigma2/settings
resolve: -> /etc/enigma2/settings
]]>
</enigma2crashlog>