vu+solo2 avermedia volar green hd

[netlom]

good morning,
I have the vu + solo2 and try using a avermedia hd green fly, which does not recognize me.

I attached the instruction cat / proc / bus / usb / devices

as I'm missing tdt plugin, you can help me.

Thanks and sorry for my english

 

[netlom]

I want to add that after researching the net I found this thread on another forum where https://bbs.archlinux.org/viewtopic.php?pid=1211593 comment that there is a patch to work this new chip (A835B) patch https://patchwork.kernel.org/patch/1905731/ is here as I lack knowledge to the topic I leave if anyone can help.

Thank you.

 

[Shiro]

External link are not admitted.
But this time we can make exception because these are links to linux and kernel tech boards

 

[dpeddi]

The patch will be included in next image

 

[netlom]

Shiro Sorry will not happen again.

dpeddi thanks, wait for the next image.

Thanks

 

[netlom]

new image installed 2.0 and still does not recognize the TDT
Have you included the patch?

Thanks

 

[dpeddi]

The patch should be included. Please provide the output of dmesg command from command line with pen inserted

 

[netlom]

if only a part of dmesg



WARNING: You are using an experimental version of the media stack.
As the driver is backported to an older kernel, it doesn't offer
enough quality for its usage in production.
Use it with care.
Latest git patches (needed if you report a bug to linux-media@vger.kernel.org):
Custom Black Hole build
usbcore: registered new interface driver dvb_usb_it913x
it913x: Chip Version=01 Chip Type=9135
it913x: Remote propriety (raw) mode
it913x: Dual mode=0 Tuner Type=38
usb 2-1: dvb_usb_v2: found a 'Avermedia A835B(3835)' in cold state
usb 2-1: dvb_usb_v2: Did not find the firmware file 'dvb-usb-it9135-01.fw'. Please see linux/Documentation/dvb/ for more details on firmware-problems. Status -2
usb 2-1: dvb_usb_v2: 'Avermedia A835B(3835)' error while loading driver (-2)
usb 2-1: dvb_usb_v2: 'Avermedia A835B(3835)' successfully deinitialized and disconnected
__clk_enable: network [1]
__clk_enable: enet [1]
bcm40nm_pm_genet_enable 00
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0: Link up, 100 Mbps Full Duplex
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
svc: failed to register lockdv1 RPC service (errno 124).
[LCD]: unknown cmd 0x1015
[CI]: CI interface initialised

eth0: no IPv6 routers present

 

[netlom]

good
already recognized, I downloaded a file it9135 internet, I've changed the name to it9135-01 and finally recognizes it and I can see the channels.

Many of the channels are pixelated, can be due to the downloaded file? or should we refine the driver.?

thanks

 

[angelofsky1980]

good
already recognized, I downloaded a file it9135 internet, I've changed the name to it9135-01 and finally recognizes it and I can see the channels.

Many of the channels are pixelated, can be due to the downloaded file? or should we refine the driver.?

thanks

I will add the firmware file to the image in the next days ....

 

[angelofsky1980]

I've found the firmware files needed and will be included in the next BH ... for your use, I will post it an IPK when I prepare it this evening.

 

[Oliverte740]

Thank you, works fine with BH 2.0.1

 

[CoPeRniX]

Sorry,

I'm Volar green with chipset A835B and BH 2.0.2 not reconigset tuner TDT.

where I can get the driver ipk??

Thanks.

 

[angelofsky1980]

Sorry,

I'm Volar green with chipset A835B and BH 2.0.2 not reconigset tuner TDT.

where I can get the driver ipk??

Thanks.

Too generic.
Follow instruction on the thread http://www.vuplus-community.net/board/threads/usb-tuner-howto-report-problems.621/ to report some infos about your USB DVB device.

 

[dpeddi]

It should be supported, please follow angelofsky suggestion

Inviato dal mio U8800Pro con Tapatalk 2

 

[CoPeRniX]

(You have insufficient privileges to reply here.

I'm not reply.

 

[dpeddi]

I confirm that black hole should support this pen from about 3 month. Please follows angelofsky instrunction.

 

[CoPeRniX]

Thanks.