There is a problem with BH in SOLO SE and SOLO2 with chipset IT9135, only work perfectly in Zero. The problem is in the boot when run system no detect nothing, this maybe because no load the drivers, i dont know .
In Solo SE for example:
If the receiver is ON and connect the T119, install drivers correctly but when i do reboot no detect tuner and usb. You can view with the commands lsmod and lsusb this:
T119 connect with receiver OFF and after run system.
root@vusolose:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0002
Bus 005 Device 001: ID 1d6b:0001
Bus 006 Device 001: ID 1d6b:0001
Bus 007 Device 001: ID 1d6b:0001
Bus 008 Device 001: ID 1d6b:0001
root@vusolose:~# lsmod
Module Size Used by Tainted: P
ext2 56975 0
brcmfb 1254 4
dvb_bcm7241 8274895 1 brcmfb
procmk 1668 1 dvb_bcm7241
ipv6 326329 12 [permanent]
T119 connect with receiver ON:
Bus 002 Device 002: ID 048d:9006
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0002
Bus 005 Device 001: ID 1d6b:0001
Bus 006 Device 001: ID 1d6b:0001
Bus 007 Device 001: ID 1d6b:0001
Bus 008 Device 001: ID 1d6b:0001
root@vusolose:~# lsmod
Module Size Used by Tainted: P
ext2 56975 0
tuner_it913x 4980 1
af9033 24726 1
dvb_usb_af9035 14265 0
dvb_usb_v2 14286 1 dvb_usb_af9035
bh_dvb_core 87907 1 dvb_usb_v2
bh_rc_core 18935 3 dvb_usb_af9035,dvb_usb_v2
brcmfb 1254 4
dvb_bcm7241 8274895 1 brcmfb
procmk 1668 1 dvb_bcm7241
ipv6 326329 12 [permanent]
AFTER Reboot
root@vusolose:~# lsusb
Bus 001 Device 001: ID 1d6b:0002
Bus 002 Device 001: ID 1d6b:0002
Bus 003 Device 001: ID 1d6b:0002
Bus 004 Device 001: ID 1d6b:0002
Bus 005 Device 001: ID 1d6b:0001
Bus 006 Device 001: ID 1d6b:0001
Bus 007 Device 001: ID 1d6b:0001
Bus 008 Device 001: ID 1d6b:0001
root@vusolose:~# lsmod
Module Size Used by Tainted: P
ext2 56975 0
brcmfb 1254 4
dvb_bcm7241 8274895 1 brcmfb
procmk 1668 1 dvb_bcm7241
ipv6 326329 12 [permanent]
I got to work the T119, with these steps:
1) Connect the T119 to the receiver.
2) Connect the usb With the firmware to the receiver also the cable Rj45
3) Turn on the receiver and install the firmware.
4) When you start the wizard, and get to the settings tuners, you can see the T119 installed and work perfectly.
Bye.