LNB's connection

It shouldn't make any difference, which cables, you attach to which tuner, you just need to get the tuner settings correct, in the menu options.
Personally I would set each up separately, to check that they are working, starting with the unicable.
Which image are you running, Black Hole, Open Black Hole, other?
 
OpenPLI. I must have done something wrong earlier, as a lot of channels freezes. I tried to change the cables, but with the same result. There's something I don't get/understand. Started from scratch yesterday with the unicable on the upper input. Everything worked OK then. But, when I tried to add the other cable, I was not able to "find it". I have tuners A to J, where I and J are C/T2, and not connected to anything.
At first I used tuner A to H for 8 channels from the unicable. (I thought I could use up to 32 channels, but maybe the receiver has a limit of 8 from the unicable?).
 
Tuner A an B are your hardware Sat tuners C,D,E,F and so in are virtual tuners used with your Unicabel LNB.

So leave the setup for Tuner A since its working
Then setup Tuner B as simple with your other LNB and Diseq

And rest should be easy and if not using the C/T2 tuners then disable them
 
Tar dette på Norsk ;)

Ta en titt på baksiden så du er sikker på at du har ditt SatCR/Unicabel LNB koblet til tuner A
Så setter du i Tuner B kabeln till din andre satellit som bruker diseq.

Nå går du in på Tuner Setup og endrer Tuner B til simple å aktiverer at du har Diseq.
Velg A,B og C som diseq så velger du korrekt satellit til rett diseq port.

Tuner A velger du Advanced og under LNB velger du SatCr ikke Universal LNB
Nedanfør i samme menyen så finner du fabrikat på ditt SatCr LNB (ex Triax) og type (001)

La alle andre tuner stå på auto og restar boksen.

Nå bør du ha mist 2 fungerande tuners sen er det bare og la automatikken ta seg av de andre :)
Eller så må du stille in det samme på Tuner C Tunder D og Tuner E som du har på Tuner A
Husk bare og bytt channel fra scr 001 til scr 002 osv hvis det ikke skjer automatiskt.

Her er screenshoot på mitt oppset. Første er Tuner A (Hardware Tuner)
Screenshoot 2 er Tuner C (Virtuell Tuner)

tunersetup.jpg

tunersetupC.jpg
 
Det fungerer sånn nogen lunde nå, men jeg har med meg det drittet med 0.9 og 19.2 øst på ingang A, men det er jo ikke på den! Så ofte når tuneren egentlig skal vise en kanal fra 19.2e prøver den å vise den fra den ingangen, men 19.2 er jo ikke der.
 
Når du åpner tuner instillinger og gjør endringer så får du spørsmål om du vill slette satellitter som ikke er i bruk for den tunern, der har du mest sannsynligvis svart "Nei" ;)

Så gjør en endring på tuner A til simpel og velg satellit 0.8 west. Når du sen sparer instilllinger så svarer du ja for og slette ubrukte satelliter.
Så starter du om og setter den tilbake til den korrekte innstillingen da skal det ordne seg :)

Blir mye svorsk nå men trur du skjønner hva jeg mener?
 
Apart from the fact that this is the BH/OBH forum, not the OpenPli one... ;) ... maybe if you get back to English we can be helpful, too... ;)
 
Well the thread started with English and no one did respond since its not a BH/OBH image in use
and since we are both speaking a language not supported here at Vu+ Community we could not move the conversation to a proper thread
and he is asking about the tuner setup on a Vu+ STB and in my opinion this has nothing to do with what image is in use.

He has try so many settings for the tuners that a new fresh flash of image is the best option

And a hint ;) Google translate works also with Swedish and Norwegian language not only Italian and Spanish :)
 
Yes, but I don't rely on Google. That's why I use it just occasionally and trying to stay as simpler as possible ;)
I don't understand (as he uses the graphical buttons for YES/NO instead of this more clear and simple words) if the Tuner A is set as
Connected: NO
This configuration is very similar to mine, a mix of Universal and Unicable LNBs, which perfectly worked before 4.1.018 and now has got issues.
But one thing is SURE: it is needed to set the DiseqC command for each tuner and each LNB and, instead, I see it is not set.
 
There is nothing wrong with your tuners its all the settings that have corrupted your settings


Is it the CanalDigital LNB you are using?


Setup Tuner A as in my screenshoot above eralier post
and Tuner B like in this screenshot.

If you use other satellites just change from my settings to yours

tunerB.jpg
 
You allredy have the best Tuners so new tuners want solve your problem

You just need to configure them correct.

If you want to talk in Norwegian we can do it over PM i guarantee you that this can be fixed
 
Nor50 said:
No, Inverto LNB. I'm not able to sort it out, so I'll buy another tuner.
Click to expand...
It's not a problem of Tuner!
You might buy one hundred tuners but if you don't learn how to configure them you'll be wasting your money!

If the Tuner A is connected to a diseqc switch, as I understood from your first post, it doesn't matter if you have mixed Universal and Unicable.SCR LNBs: you must tell your CONFIGURATION to use the right port for each satellite.
Instead I see from your post #5 that you didn't set it.
 
Thanks to Thomas67 I now hope everything is OK. I have flashed a new image and that hopefully deleted all errors from previous set-ups.
 
You must log in or register to reply here.
Back
Top